產品簡介：
淨味肪潮防黴膩子是採用優質天然粉料，添加特殊複合添加劑及耐水資料而製成的內牆乾粉膩子。 本品採用淨味配方，施工時無明顯氣味，綠色環保。 批刮後效果細膩平滑，與基層結合牢固，耐水耐鹼性佳。 開封後加水攪拌即可使用，施工方便，本產品適用於室內牆面和頂面處理，尤其對潮濕環境或粘結强度要求較高的牆面和頂面的平整處理效果更佳。

適用範圍：
本產品適用於室內一般牆面和頂面塗刷塗料之前批刮及整平處理。

國内大倉庫，直接上港車發到香港澳門。出口業務順利開展。

使用方法：
施工前應確保基層乾燥、結實、無油污及其它鬆散物。 若原牆面基層批過老粉、石膏粉、紙筋石灰等必須全部剷除乾淨，並做好介面處理。
本產品推薦配比為“粉料：水=1：0.33-0.4”，調配成均勻膏糊狀，稠度以施工方便為准。
施工應分次進行批刮，推薦單道批刮厚度最大不超過2mm，以每道1mm道為宜，主要因為分次薄層批刮更有利於提高膩子層間强度及批刮後細膩狀態，同時减少開裂風險。
用批嵌工具進行施工，一般需批兩道以上，兩道批刮間隔時間以前一道批刮膩子實幹為判斷依據，實幹後可批刮下一道。
膩子層完全乾燥後，宜根據施工環境選用合適砂紙在24h內進行打磨。 間隔時間越長越難打磨。 打磨時將刀痕輕輕磨平即可，勿過度打磨以免影響强度。

推薦用量：
（1.1~1.5）kg/mm/㎡，推薦用量可能因實際基層平整度不同有所差异，以實際為准。

注意事項：
施工溫度建議在5~35℃，空氣相對濕度≤85%條件下施工。
調配好的膩子在常溫（25c）下可使用時間約為2小時，建議根據環境溫度現配現用。
切忌將調配後已幹結的膩子再次加水混合使用。
過於乾燥的基層牆體可用適量水潤濕，晾至無明水在再行膩子批刮。 面層膩子批刮不宜太薄，避免因失水過快導致强度下降。
膩子批刮應薄層多道，厚批有起殼風險，總厚度不得超過3mm。
開封後的產品建議一次使用完畢，未使用完的產品，應密封儲存並儘快使用，避免受潮影響使用效果。

Product Introduction:

Jingwei Fat Moisture Anti Mold Putty is an interior wall dry powder putty made from high-quality natural powder, added with special composite additives and water-resistant materials. This product adopts a clean and odorless formula, with no obvious odor during construction, and is environmentally friendly. After scraping, the effect is delicate and smooth, firmly bonded to the base layer, and has good water and alkali resistance. After opening, add water and stir for easy use. This product is suitable for indoor wall and ceiling treatment, especially for smooth treatment of walls and ceilings in humid environments or with high bonding strength requirements.

Scope of application:

This product is suitable for scraping and leveling indoor walls and ceilings before applying paint.

usage method:

Before construction, ensure that the base layer is dry, solid, free of oil stains and other loose materials. If the original wall base has been treated with old powder, gypsum powder, paper reinforcement lime, etc., they must be completely removed and the interface treated properly.

The recommended ratio for this product is "powder: water=1:0.33-0.4", which is blended into a uniform paste with a consistency that is convenient for construction.

Construction should be carried out in batches, and it is recommended that the maximum thickness of a single batch should not exceed 2mm, with each batch being 1mm. This is mainly because batch scraping in thin layers is more conducive to improving the strength between putty layers and the delicate state after scraping, while reducing the risk of cracking.

When using batch embedding tools for construction, generally two or more batches are required. The interval between two batches is based on the fact that the previous batch of putty is dry, and the next batch can be scraped after it is dry.

After the putty layer is completely dry, suitable sandpaper should be selected according to the construction environment and polished within 24 hours. The longer the interval, the harder it is to polish. When polishing, gently smooth out the knife marks and do not over polish to avoid affecting the strength.

Recommended dosage:

(1.1~1.5) kg/mm/㎡, the recommended dosage may vary depending on the actual flatness of the base layer, and the actual amount shall prevail.

matters needing attention:

The construction temperature is recommended to be between 5-35 ℃ and the relative humidity of the air should be ≤ 85%.

The prepared putty can be used for about 2 hours at room temperature (25 ° C), and it is recommended to prepare and use it according to the ambient temperature.

Do not mix the dried putty with water again after mixing;

Overly dry base walls can be moistened with an appropriate amount of water and left to dry until there is no visible water before applying putty and scraping. The surface putty should not be scraped too thin to avoid a decrease in strength due to rapid water loss.

The putty scraping should be done in thin layers and multiple passes, and there is a risk of shell peeling for thick batches. The total thickness should not exceed 3mm.

It is recommended to use the opened product in one go. Unused products should be stored in a sealed container and used as soon as possible to avoid moisture affecting their effectiveness.