立邦Nippon牌膩子粉。白色。

使用範圍廣。價廉實惠。

20KG每包，適合室内批蕩使用。

歡迎來電訂購+852-67274664

產品簡介：

美加儷膩子是採用優質天然粉料，添加特殊複合添加劑而成的內牆乾粉膩子。 本產品採用淨味科技，施工時無明顯氣味，綠色環保，批刮後效果細膩均勻，與基層結合牢固，耐久堅固。 開袋後加水攪拌即可使用，施工方便，易打磨。

適用範圍：

本產品適用於室內幹區與塗料搭配的牆面和頂面批塗處理。

送貨到澳門，感謝客戶的信任采購。

適用範圍：
本產品適用於室內幹區與塗料搭配的牆面和頂面批塗處理。

使用方法：
施工前應確保基層乾燥、結實、無油污及無它鬆散物。 若原牆面基層批過老粉、石膏等必須全部剷除乾淨，並做好界面處理。
本品推薦配比為“粉料：水=1 : 0.33-0.4”，調配成均勻膏糊狀，稠度以施工方便為准。
施工應分次進行批刮，推薦單道批刮厚度最大不超過2mm，以每道1mm為宜，主要因為分次薄層批刮更有利於提高膩子層間强度及批刮後細膩狀態，同時减少開裂風險。
用批嵌工具進行施工，一般需批兩道以上，兩道批刮間隔時間以前一道批刮膩子實幹為判斷依據，實幹後可批刮下一道。
膩子層完全實幹後，方可進行打磨和塗料施工。

推薦用量：
（1.1-1.5）kg/mm/㎡，推薦用量可能因實際基層平整度不同有所差异，以實際為准。

注意事項：
施工溫度建議在5-35℃，空氣相對濕度≤85%條件下施工。
調配好的膩子在常溫下可使用時間約為4小時。
切忌將調配後已幹結的膩子再次加水混合使用。
開封後的產品建議一次使用完畢，未使用完的產品，應密封儲存並盡快使用，避免受潮影響使用效果。

Product Introduction:

Meijiali putty is an interior wall dry powder putty made of high-quality natural powder and special composite additives. This product adopts clean odor technology, with no obvious odor during construction, green and environmentally friendly. After scraping, the effect is delicate and uniform, and it is firmly combined with the base layer, durable and sturdy. After opening the bag, add water and stir to use. It is easy to apply and polish.

Scope of application:

This product is suitable for wall and ceiling batch coating treatment in indoor dry areas with paint matching.

usage method:

Before construction, ensure that the base layer is dry, solid, free of oil stains and other loose materials. If the original wall base has been coated with old powder, gypsum, etc., it must be completely removed and the interface treated properly.

The recommended ratio for this product is "powder: water=1: 0.33-0.4", which should be mixed into a uniform paste with a consistency that is convenient for construction.

Construction should be carried out in batches, and it is recommended that the maximum thickness of a single batch should not exceed 2mm, with each batch being 1mm. This is mainly because batch scraping in thin layers is more conducive to improving the strength between putty layers and the delicate state after scraping, while reducing the risk of cracking.

When using batch embedding tools for construction, generally two or more batches are required. The interval between two batches is based on the fact that the previous batch of putty is dry, and the next batch can be scraped after it is dry.

After the putty layer is completely dry, polishing and coating construction can be carried out.

Recommended dosage:

(1.1-1.5) kg/mm/㎡, the recommended dosage may vary depending on the actual flatness of the base layer, and the actual amount shall prevail.

Attention:

The construction temperature is recommended to be between 5-35 ℃ and the relative humidity of the air should be ≤ 85%.

The prepared putty can be used for about 4 hours at room temperature.

Do not mix the dried putty with water again after mixing.

It is recommended to use the opened product in one go. Unused products should be stored in a sealed container and used as soon as possible to avoid moisture affecting their effectiveness.